i love bedding! summer bedding, fall bedding, pillows, throws, you name it. this project is inspired by the beautiful bedding textiles designed by. i’ve taken a simple cotton duvet and “block” printed a pine cone design, but instead of using expensive wood or linoleum blocks, i made a makeshift block from scrap cardboard (free!). this project takes a little more time and patience then the last textile makeover, but the results are really beautiful and this can be a very inexpensive bedding update for whenever you need it. have fun! –
CLICK HERE for the full project after the jump!
1. scrap cardboard (you need one or two large flat pieces with no bends or tears that can fit your stencil)
2. newsprint or scrap paper (this should also be as big as your stencil, and you will need at least ten sheets of this)
3. fabric paints (you can custom mix your color like i did using several colors. you will need at lot of paint for this, at least enough paint to fill a regular sized plastic drinking cup)
4. paint tray (or paper plate) and small foam roller
5. exacto knife and extra blades
6. large working surface
7. permanent marker
9. duvet (or fabric to make duvet, or a cotton sheet, etc. – whatever you desire to print!)
10. plastic cup
(note before starting: if you want to spend more money to purchase a large linoleum block, it will provide you will a sharper, cleaner printed image. this project is to show you that you can get a pretty nice image that may suit your style with a cheap material like cardboard. but it does create a rough, imperfect look. also, if you want to make your design smaller (fist-sized for example), i would also recommend using a linoleum block. the method described here is best for bigger prints.)
to make the cardboard printing “block”:
1. draw your image, including the parts you plan to cut out. when planning your design, try to keep it simple, with big shapes. you don’t want anything too intricate or dainty as the cardboard can’t be too thin or it will break down. try to keep all printing surfaces of the cardboard at least .5″ thick.
2. when you have your design drawn, use the exacto knife to cut out the shapes that need to be removed. what is left will be exactly what your painted surface will look like.
3. when you are happy with the final design, trace it onto your cardboard with the permanent marker, including all the cut out parts.
4. now cut your design carefully out of the cardboard. make sure all cuts are clean. replace your blades often to keep the cuts sharp and clean.
to print the design:
1. prep your fabric according to the directions on your fabric paint and iron out wrinkles. lay on work surface.
2. decide how you plan to print your design. if you want exactness, you need to measure on your duvet and make small marks with a pencil or tape to show where you want to place the block each time. otherwise, you can start at the top of the duvet and work downwards, eyeballing the design as you go. this will probably lead to minor imperfections in alignment, which i have too, but i didn’t mind.
3. mix your paints and prepare a large amount of paint in the plastic cup. you want the paint to be the consistency of house paint from the can. if you bought thicker fabric paint, you may need to dilute with water.
4. pour some of the paint in the paint tray and cover your foam roller evenly with paint. you want a lot of paint on the roller. roll the paint onto the cardboard and cover evenly.
5. to print the design, place the cardboard paint side down onto fabric. cover it with a piece of clean scrap paper or newsprint and use one hand to hold the cardboard in place while using the other hand to press down and rub over the entire image. press firmly and make sure you get every inch of the surface of the cardboard. it is similar to if you were gluing the cardboard down, you want to smooth over the entire surface firmly to make sure every inch of the surface is pressed into the fabric. then you remove the paper and carefully peel the cardboard off, using one hand to hold fabric down as you peel up the cardboard.
6. you want to print the pattern on scrap paper or fabric a few times before you place it on your actual duvet surface. this will the give the cardboard a couple times to soak in the paint so it will release more paint onto the fabric. this is also good practice to see how much paint you need and how firmly you need to rub on the design. do not skip this step!!
7. once you have the printing process down, begin printing on your duvet one print at a time. your cardboard pattern should hold up for the whole process. if you are doing both sides of the duvet, you will need to make two cardboard shapes and use a fresh one for the flip side. the first one will start to break down after 30 uses or so.
8. continue printing your pattern. keep using fresh sheets of paper to cover and press down. make sure you do not get extra drips or smears of paint on the fabric.
9. leave your duvet laying flat somewhere to dry. you may need a helping hand to help you transport it or hang it somewhere.
10. follow the steps on your fabric paint for how to set the pattern. this will allow you to wash the fabric again and again without losing your pattern.