when we decided to move our bedroom to a different room in the house, we no longer had the space for our old bedside tables. i decided to use an old chair because it was narrow enough and it looked pretty good. unfortunately, i lost two important things in the switch: a place for private things (my ‘goody’ drawer, so to speak, although mine just has a journal and some nail clippers…saucy!!) and surface space – even with a smaller bedside lamp i didn’t have much room. i loved the quirkiness of using a chair (i’ve seen in many home tours and it is always very charming), but i needed these problems solved. to the rescue!!
i am majorly inspired by “odd” furniture designs, like this “” by florian kallus, so i decided to work over a simple pine chair to create a multi-purpose bedside table, complete with a drawer and swivel lamp! i splurged a bit on the new trål wall sconce ($16.99) because it looked so good with the chair, and i like that it rotates so i can change the angle when i am reading in bed. if you aren’t into the industrial look of this piece (my boyfriend called this franken-furniture, which i love), i hope you will at least take away the knowledge that adding a drawer to a chair (or anything) is remarkably easy, and cheap! the great thing about this design is that you can still use the chair for seating if you need to, you can even have a little light over your shoulder! i hope you like this one, i had a lot of fun making it. have fun!! –
CLICK HERE for the full how-to after the jump!
1. ikea chair
2. ikea sconce
3. ikea knobs (or any knob you like)
3. wood box or crate or old drawer (must be 12″ wide and under 12″ long. i used from michael’s craft store)
4. drill (with a 3/8″ thick drill bit)
5. drawer slides 10″ long (these come in packs of two and are available at most hardware stores. they come in many lengths)
6. 1″ wood screws (x2)
ikea materials: $41
wood crate, box: free on hand, or $5 (at craft store)
drawer slides: $5
1. take the chair out of the box and connect the two side pieces with the back slats of the chair, according to the instructions. lay the seat on top, but do not attach.
2. take your drawer/box and slide under the seat in front to check the fit. the box from michael’s fit perfectly with the 12″ side as the front of the drawer.
3. take the drawer slides apart and attach the slides to the drawer according to the instructions that come with the drawer slides. you should have small screws included with the drawer slides that you can use. it’s okay if your drawer does not go the full length of the slides (my box was just 8″ wide, so 2″ of slide were extending on the back of the drawer). make the drawer slides flush with the front of your drawer, and screw in a couple places on each side to secure. you might want to add a piece of wood to the back for weight. i used the extra front panel piece of the chair that was left over.
4. now that your drawer has the slides attached, take the seat off the chair so the interior of the sides of the chair are exposed. attach the other two pieces of the drawer slides to the left and right side of the chair. make them flush with the top edge of the sides, so that they seat will be right on top of them and the drawer. you can put your drawer in while holding the sides to make sure you have them in the right place. a second person is useful here for this purpose.
5. screw the front of the drawer slides into the chair legs with one screw on each side. then screw in the back of each drawer slide with the 1″ screws (to account for the gap between the slide and the wood of the chair).
6. now that your drawer slides are in, your drawer should slide into them easily. you will notice that the front of the chair is adjustable in width, because the seat hasn’t been attached yet. adjust their width so that the drawer is sliding in without any friction.
7. when you have the drawer in the right place and sliding properly, put the seat back on and screw in place using the screws that came with the chair. make sure the drawer still slides nicely when the seat is put in place.
8. drill a hole in the center of the front of the drawer and add the snodd knob. super cute! slide drawer back in place.
9. unwrap the sconce and read the directions for installation. it’s WAY too easy.
10. take the metal piece that attaches to the “wall” and screw it into the back of the top of the chair on the left side (or right, depending on which side of the bed your chair is going on)
11. slide the sconce piece onto the metal piece and add the pin to secure. add light bulb. if you want, you can staple the cord down the back of the chair to keep it neat, but it’s pretty easy to hide and tuck away also.
12. put next the bed and plug it in. hide goodies in drawer.